Hello,
I'm messing around with the Fit-PC2, and after installing Ubuntu 11.04, the wireless refuses to connect to my AP. Is there any special driver or steps that have to be taken to get this working?
- pez
WiFi not working
Re: WiFi not working
Did you get it working?
It was working last night for me, I rebooted and now it says:
This is what I see in dmesg
Anyone?
It was working last night for me, I rebooted and now it says:
Code: Select all
# wpa_supplicant -i wlan0 -Dwext -c /etc/wpa_supplicant.conf
Could not set interface wlan0 flags: Input/output error
Failed to initialize driver interface
# ifconfig wlan0 up
SIOCSIFFLAGS: Input/output error
Code: Select all
[ 10.232396] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.237375] Registered led device: rt2800pci-phy0::radio
[ 10.237738] Registered led device: rt2800pci-phy0::assoc
[ 10.238068] Registered led device: rt2800pci-phy0::quality
[ 12.364036] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 12.364486] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 13.988038] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 13.988508] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 133.272061] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 133.272955] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 217.800078] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 217.800973] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 246.852071] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 246.852968] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 250.560086] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 250.560980] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 268.192080] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 268.192975] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 553.348081] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 553.370710] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
[ 564.996091] phy0 -> rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 565.040474] phy0 -> rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5).
Re: WiFi not working
It seems the compat-wireless is broken on 2.6.38 and Ubuntu stopped doing backports for it - Installing compat-wireless-2011-07-05 solved the issue for me.
Instructions here:
http://wireless.kernel.org/en/users/Download
Instructions here:
http://wireless.kernel.org/en/users/Download